Ịcha akwụkwọ
I. Nkwadebe
1) Debe ebe ọrụ dị ọcha.
2) Ndị na-arụ ọrụ kwesịrị iyi ihe mkpuchi ugogbe anya nchebe. Yiri earplugs na akpụkpọ ụkwụ nchekwa ma ọ bụrụ na ọ dị mkpa.
3) Machibido iji ngwá ọrụ eletrọnịkị ebe a na-arụ ọrụ iru mmiri.
2. Ịcha
1) Tinye osisi na tebụl trimming horizontally
2) Bee si n'akụkụ mma iji zere ọdịiche dị n'elu.
3) Bee n'ogologo iji jide n'aka na otu ntụziaka njikọ mgbe egwuregwu.
3. Ngwá ọrụ akwadoro
1) Ịcha mma nko (tinye na hpl laminate)
2) Nkwọcha ịkpụ-sweep saw (tinye na hpl laminate)
Nhọrọ agụba:
A.Zigzag agụba etinye iji bee hpl laminate na kọmpat(belata chipping)b.Agụba eze na-enweghị eze na-etinye iji bee bọọdụ na-anaghị ere ọkụ(bọọdụ ahụike.
3) igwe ịcha-sliding table saw
4. Drilling (na-abụghị combustible osisi ahụike osisi)
1) Jiri 60 ° -80 ° pụrụ iche rọba ọkpọ ọkpọ forcompact, pụrụ iche osisi ciment akuakuzinwo fornon-inflammable / ọgwụ osisi.
2) Ka ịzenarị ụzọ ọpụpụ oghere gbajiri agbaji, ọsọ a na-egwupụta ihe na ịpị ya kwesịrị iji nke nta nke nta belata.
3) Tinye otu obere osisi ma ọ bụ plywood n'okpuru oghere iji zere ụzọ ọpụpụ oghere gbajiri.
4) kpuru ìsì (tinye na kọmpat)
a.Dịgharịa n'ihu dị ka foto a
b.Dịgharịa n'akụkụ dị ka foto
c.Dayameta nke oghere ahụ dị 0.5mm pere mpe karịa ịghasa.
5) Iji zere nchekasị ịta craze. Zere na-apụta ìhè n'akuku mgbe mkpọpuo the hole.Na-atụ aro niile nke interiorangle na-opekempe ekwe radius 3mm.The otherangle na akụkụ kwesịrị okokụre were were.
5. Mbelata
1) Jiri trimmer mechaa akụkụ nke kọmpat. Mgbe emechara nke ikpeazụ iji aka dị mma, biko jiri faịlụ aka na scraper Joiner.
2) Rouch n'akụkụ mgbe ewepụtụ mina nke kọmpat / na-abụghị inflam mable osisi / ọgwụ osisi nwere ike polished aka.Afteipolished, na-eji wax ka mma n'akụkụ na dịpụrụ adịpụ site wet.The kọmpat nwere ike ejikwara chamfering, moldingslotting na wdg.
3) Ekwesịrị iwepụ ihe nkiri nchebe ahụ ruo mgbe emechara nhazi.Biko wepụ ihe nkiri ahụ n'akụkụ abụọ n'otu oge ahụ.
Oge nzipu: Eprel-25-2023